EMC, Power Quality and Protection
TOSHIBA
The following devices are specifically designed to provide protection, reduce EMI and improve the power quality (ie. power factor, harmonic distortion, surge suppression) of Toshiba TOSVERT inverter drives. Please feel free to contact us for more information. We are also able to perform power quality measurements and analysis on-site to help you select the optimal solution that complies with power quality standards or requirements
 
Benefits of Reactors and Filters
 
  • Increase Drive System Reliability
  • Reduce Harmonics
  • Reduce dv/dt (EMC)
  • Reduce Motor Noise and Temperature
  • Improve True Power Factor
  • Filter Power Line Disturbances
  • Reduce Surge Currents
  • Extend Transistor Life
  • Reduce Voltage Doubling Effects
  • Absorb Power Line Spikes
 
Comparison of DC reactor and AC reactor
Reactor Efficiency
Power factor improvement Harmonics reduction External surge voltage reduction
Ac reactor o o o
DC reactor oo oo x
 

AC Reactor
The AC reactor is used to improve the input power factor of the inverter power supply, reduce harmonics and/or suppress external surges. Joint usage of the DC reactor with the AC reactor will provide high reliability operation of TOSVERT inverter for suppressing external surges.
For: All Tosvert series
　
 

DC Reactor
The DC reactor is used to improve the input power factor of the inverter power supply and reduce harmonics. The DC reactor is more effective than the AC reactor in improving the power factor and reduce harmonics.
For: All Tosvert series (some models have built-in DC reactor)
　
 

EMI Filter
Most TOSVERT series inverter drives have built-in EMC noise filter. But when you need to comply with a higher standard or connected to long motor cable between inverter drive and motor, please use an external EMI filter.
For: All Tosvert series
 

Braking Resistor
Frequent start-stop operation, sudden braking or when the deceleration time must be shortened on loads with large inertia will generate and dissipate excessive heat energy. The braking resistor is used to absorb the energy.
For: All Tosvert series
　
 

Active Front-End Hamonic Filter
The SC7 can greatly reduce harmonics on the power side and assure the operations at high power factor.
For: All Tosvert series
 

 
Communications
 

TOSHIBA
With one of the broadest sets of supported industrial protocols in the industry, Toshiba drives can easily communicate with your network. With little or no setup required, genuine Toshiba option cards offer an almost plug and play installation and seamlessly integrate into your network. The built-in communication options provides the interface between industrial networks and inverter drives. The communication modular terminal blocks are ideal for space saving and centralized control systems.

 

DEV001Z: DeviceNet Communication Option Board
Built-in DeviceNet interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1 
　
 

RS4003Z: RS485 Communication Option Board
Built-in RS485 interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1 
 

LIU005Z: LonWorks Communication Option Board
Built-in LonWorks interface for VF-S11 inverter
For: Tosvert VF-S11, VF-FS1
 

Communication Terminal Block Expansion Option
 - DEV002Z: Built in DeviceNet card for VF-AS1/PS1
 - PDP002Z: Built in Profibus DP card for VF-AS1/PS1
 - CCL001Z: Built in CC-Link card for VF-AS1/PS1
For: Tosvert VF-AS1, VF-PS1
 

I/O Terminal Block Expansion Option
 - ETB003Z: 4 digital inputs, 2 digital outputs, 1 relay output, 1 PTC input
 - ETB004Z: all ETB003Z I/O's + 2 analogue inputs & 2 analogue outputs
For: Tosvert VF-AS1, VF-PS1
 

No Picture
Available

 TOS-SN-2: RS485 Communication Interface
External RS-485 Interface
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
 

Network Options
RS485 (Modbus®RTU/TOSHIBA), PROFINET®, DeviceNetTM, PROFIBUS®-DP, EtherCAT®, CANopen®,CC-Link®, LONWORKS®, BACnet®, Metasys®N2, APOGEE®FLN
For: Tosvert VF-AS3, VF-S15
 
 

Industrial Control Communications
Specializing in the engineering and manufacturing of embedded communication and control solutions for factory automation, networked controls, and building automation systems. The ICC Network Gateway Series is designed for Toshiba inverter drives to provide a uniform interface, configuration and application experience. This commonality reduces the user's learning curve, reducing commissioning time while simplifying support.
 

PBDP-110: External Profibus Interface
Provides Profibus connectivity to Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
 

MBP-100: Modbus Plus Network Gateway
Provides connectivity between Modbus Plus, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
 

DNET-100: DeviceNet Network Gateway
Provides connectivity between DeviceNet, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
 

ETH-200: Ethernet Multi-Protocol Network Gateway
Provides connectivity between Ethernet, RS-485 and RS-232 based fieldbus protocols and/or Toshiba inverter drives.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
　
 


 
Remote Keypads & HMI Interfaces
Toshiba allows you to mount your inverter drive somewhere else while keeping the control close to you. With plain English displays and the ability to store drive parameter sets available on some units, these keypads can make it even easier when using your new Toshiba inverter.
 
TOS-SN-1: Extension control panel
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-S11, VF-FS1, VF-nC1, VF-A7, VF-P7
 
TOS-SN-10: Extension control panel
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-AS1, VF-PS1, VF-nC3, VF-S15
 

RKP001Z: Toshiba Remote control keypad  
Display 4 digit LED. Inverter's built-in panel functions.
For: Tosvert VF-S11, VF-FS1, VF-nC1
 

RKP002Z: Toshiba Remote control panel
Display 4 digit LED. Parameter copy & memory function. Easy Key
For: Tosvert VF-AS1, VF-PS1, VF-S11, VF-FS1, VF-nC1
 

RKP004Z: Toshiba Remote High Resolution LCD panel
LCD Display w/backlight. Language selection. Jog dial + 4 function keys.
For: Tosvert VF-AS1, VF-PS1
 

　
PC-Link Cables
Connect your Toshiba inverter drive with any PC/notebook using one of the following cable options to configure, operate and monitor the inverter drive with the easy-to-use PCM software. (Note: PCM software is included and available for download)
　
 

TOS-SN-3: RS232/USB PC-Link cable
Data communication between PC's RS232c serial or USB port with inverter drive.
For: Tosvert VF-S11, VF-FS1, VF-nC1　
 

TOS-SN-9: USB PC-Link cable
Data communication between PC's USB port with inverter drive.
For: Tosvert VF-AS1, VF-PS1, VF-nC3, VF-S15
 

USB001Z: USB PC-Link cable
Data communication between PC's USB port with inverter drive.
For: Tosvert VF-S15, VF-AS1, VF-PS1, VF-S11, VF-FS1, VF-AS1, VF-nC1
　
 

Multi-loader : mobile parameter writer
Multi loader integrates parameter writer that can transfer configuration files to VFD. With multi loader you can set the parameter without connecting VFD to power source.
For: Tosvert VF-S15, VF-AS1, VF-PS1, VF-S11, VF-FS1, VF-AS1, VF-nC1
 


© 2019 Sunnice Supplies Co., Ltd all rights reserved.